How to Make a Stationary Video from a Manual Circular Paper

Natalya August 5, 2019

Phil B from instructables.com shared his experience converting a handheld circular saw into a circular saw. Further from his words.

When working in the workshop, I sometimes need to cut long pieces. This is best done with a stationary circular saw, but I don't have one.

But there is a Porter-Cable hand-held circular saw model PC15TCSMK, which I decided to convert into a circular saw. Moreover, the alteration allows you to use it in 2 versions, as well as a collapsible workbench, which I also assembled in this project to save space in the workshop.

Preparing materials and tools

The following materials were used in the work:

• 19 mm plywood 740x960 mm.
• Steel rod 6 mm.
• Threaded rod 6 and 8 mm.
• 32 wood screws, 40 mm long.
• Various nuts and washers.
• Water pipe 3/4 inch.
• Iron corner from an old bed.
• Steel electrical boxes and covers for switch and socket.
• Three Romex connectors.
• Dual 15A receptacle and 15A toggle switch.
• Electrical plug with three prongs.
• Electrical cable with rubber coating.

Tools used:

• A circular saw.
• Radial hand saw.
• Disc for cutting grooves DADO.
• Building level.
• Manual frezer.
• Hand drill.
• Drilling machine.
• Welding machine.
• Angle grinder with cutting wheel and grinding wheel.
• Hammer.
• C-clamps.
• Pliers.
• Screwdriver.

Making a tilt controller

To cut workpieces at a certain angle, I make a tilt regulator. It can swivel just over 45 degrees to the left or right.

• To do this, I first made a base from a steel plate, in which I cut a semicircular base for the lock nut.
• I screwed a steel strip on the back side of the plate - it serves as a guide for the control unit and moves along the groove in the tabletop of the circular saw.
• I attached a T-shaped stop made from scraps of plywood to the wide edge of the base. To recess the screw heads, I countersunk them.
• I made a rotary handle from a water pipe - I welded a nut into it with which I can lock the tilt regulator.

Circular saw device

Being a truly useful tool, the circular saw has a fairly simple design. Its main components:

• bed – frame on which the main units are mounted;
• tabletop with a slot for a disk;
• engine with rotation transmission system;
• cutting tool, disc with teeth.

Optionally, the device can be supplemented with a pusher, which ensures progressive movement of the workpiece towards the disk, and various lifting mechanisms that regulate the cutting depth.

The principle of operation of a circular saw (circular saw) is that the rotation of the electric motor shaft is transmitted to the cutting tool, a disk with sharply sharpened teeth. The center of the disk is located below the level of the tabletop, only a segment of it is removed from it. The workpiece is brought to the rotating disk, the teeth bite into the wood, creating an even cut.

Making a mounting plate

• To maintain as deep a cut as possible with a hand saw, I selected a 6 mm sheet of metal from which I made a mounting plate.
• I cut holes in it for the saw blade with a width sufficient to activate the tilt of the blade.
• To install it, I cut a hole in the tabletop using a hand router.
• I attached the plate to the circular saw fence with screws and placed it in the tabletop.

In fact, it turned out that the mounting plate was below the plane of the tabletop. This does not create problems for cutting long workpieces. But when sawing small parts, where accuracy is important, this position is unacceptable.

• Bring the mounting plate level to the rest of the countertop by applying several coats of automotive body putty to the steel plate. Then I sanded it thoroughly.

Building a home circular

According to reviews of many home-made carpenters, the easiest way is to convert a manual model of a circular saw into a stationary one, or, more correctly, an easel one. In this case, you can kill at least three birds with one stone:

For your information!
The main advantage of the above circular saw circuit is the well-chosen engine torque and its speed, which ensures maximum performance of the device. On a 225mm diameter drive, the offset, or height of the drive above the workbench, is only 40mm. This is more than enough to cut a magpie board into a plank or batten, cut out any shaped parts and solid wood. In addition, a spring-loaded protective cover is installed on the body of the circular saw, covering the cutting edge in the non-working position.

Perhaps this device is useful and necessary for protecting fingers and hands, but it only interferes with work, since the thin cutting edge of the disk is not visible. Therefore, when remodeling, it is often dismantled or fixed to the body of the circular saw in the open position.

Converting a hand-held circular saw into a stationary version

All that needs to be done to convert a hand saw to a stationary version of a circular saw is to make a table or box-shaped body and attach the saw to the back of the table top so that part of the cutting edge of the disk protrudes above the plane of the table, photo.

The size and shape of the circular table are selected based on the width and length of the lumber. For small boards, a one and a half meter table, 60-70 cm wide, will be optimal. The supporting part of the circular saw can be welded from a steel angle with a shelf width of 25-30 mm. Horizontal struts from reinforcement or angle are welded into the upper and lower parts of the legs. This solution allows for maximum frame rigidity.

For the tabletop you can use laminated chipboard or OSB, plywood 15-20 mm thick. In this case, the tabletop itself does not have to be positioned symmetrically relative to the steel support frame. When cutting a board on a circular saw, you have to work with both hands. With one hand we feed the material forward longitudinally, and with the other we press the board to the table. So, the main thing is that the location of the motor and the pressure point are not very close to the edge and do not create a tipping moment for the entire structure.

The plane adjacent to the cutting tool can be covered with metal or plastic to make it easier to move the solid board across the table of the circular saw.

The only drawback of this modification is the need to modify the controls: the start button and the hold lever. Most hand-held circular saws are equipped with a holding lever or trigger in addition to the start button. While you press the trigger against the handle of the saw with your fingers, the engine of the device is operating in normal mode. As soon as you release the trigger, the engine stops. A very necessary thing if, while cutting, you unexpectedly dropped a working circular saw from your hands.

Therefore, the first step is to make changes to the control system of the hand-held circular saw. To do this, the contacts on the button and trigger are connected to an external electrical package mounted on the body. Of course, such modifications can be performed for power tools for which the warranty period has long expired.

In rare cases, it becomes necessary to remove the instrument from the table and use it in its original manual form. In this case, instead of resoldering the contacts, the button and trigger are fixed with a clamp or simply wrapped with electrical tape, and the power cord from the tool is included in a carrying case with an on-off button.

The simplest option for remaking a circular saw is shown in the photo. For a tabletop circular saw, a box-shaped body is made from plywood. The tabletop with the circular saw installed is turned over and secured to the frame.

Making a guide ruler

When working with a circular saw, it is important to be able to not only cut a board, but also cut a plank or slatted strip of a given width exactly to size. To do this, a guide ruler is installed on the tabletop of the saw, which can be moved relative to the plane of the disk, and thereby select the width of the cut.

The ruler is made in the form of a steel angle. Using screws, the ruler can be relatively easily moved along the slots in the tabletop, and thereby change the size of the cut.

A simpler version of the ruler is made of pine boards, 40 mm wide and 20 cm longer than the table size. Along the edges of the board, two furniture nuts with metric threads are pressed into the lower part. Using screws, L-shaped hooks are attached to the ends of the ruler. After installing the ruler, the hooks are tightened with screws, the hooks rise and firmly fix the guide bar on the tabletop.

Finishing the bottom side of the mounting plate

The first photo shows the studs for attaching the saw. The criss-cross molded base secured to the base of the saw leaves no room for a nut.

• I added a square steel washer that I made so that the nut could work properly.
• The second mounting pin is located near the hole at the other end of the saw base. In the lower left corner of the photo you can see the stud and nut that secures the steel mounting plate into the plywood. The mounting plate fits very tightly to the plywood, especially on one side.

The second photo shows two wooden blocks for setting up the saw, attached with studs and nuts.

• A mechanical screw passes through each of them so that their tips touch the base of the saw.
• Any screw can be turned one turn to move one end of the saw base a few mm.

A simple circular saw from a grinder or circular saw

An angle grinder (grinder) is one of the most popular home craftsman tools; with its help it is easy to cut metal and clean welds. In addition, using a wood disc instead of a standard abrasive disc, the grinder can be turned into a hand-held circular saw (it is also called a parquet saw), and by making a frame with a table, it can be turned into a stationary circular saw.

Required accessories

To work you will need:

• multilayer plywood with a thickness of 10 mm or more;
• switch and wire;
• countersunk head bolts;
• screws;
• wooden block 40x40 mm.

You also need to prepare a drill or screwdriver, hammer, screwdriver, pliers, ruler and pencil. Using these tools you will have to make a circular saw with your own hands.

Of course, you must not forget the grinder itself or the hand-held circular saw. At the first stage, it will help to cut the material, and then it will take its place as the working body of the circular saw.

Sequencing

The first step is to make the body of the circular. Thick plywood is perfect for this; you can use any pressed wood boards. You will need to cut four rectangular sheets, size 40 x 80 cm. They are used to assemble a box with a square 80 x 80 cm at the base. For ease of assembly and reliability of the structure, four bars are installed in the corners.

The resulting box is closed on top with a table top. It can be made from the same plywood, but it is better to use some sheet material with a laminated coating. This guarantees the durability of the machine and ensures ease of use of the homemade circular saw.

A cut is made in the tabletop to allow the disk to come out, and holes are drilled on the sides for attaching the tool.

The grinder must be securely fixed under the tabletop. The design of the latch can be very diverse, it all depends on the configuration of the machine itself. The main requirement for fastening is that it must securely hold the angle grinder without allowing it to move.

The simplest fastening may look like this: two metal squares, a grinder is fixed between them with a steel clamp.

For additional strength, it is recommended to use the thread of the side handle; a bolt with a suitable thread is screwed into it.

Two holes are drilled in the upper shelves of the angles holding the angle grinder. The structure is secured from below to the tabletop using countersunk bolts. All that remains is to block the power button and connect the angle grinder via an external switch.

In the same way, you can make your own circular saw from a circular saw. In this case, the work is noticeably simplified due to the fact that there is no need to invent a fastening. It is enough to make a cutout for the disk, drill holes along the holes of the plate with a hand-held circular saw.

I'm making a base

To assemble the base, I used pieces of plywood and corners from an old bed frame. The green pieces connecting them are the remains of a garden fence.

• I screwed them to the countertop from the back side and welded them using a welding machine.
• I welded a handle to one of the crossbars for ease of carrying.
• I attached electrical boxes and a power switch to the plywood below.
• I use folding construction sawhorses as legs.

Why does chipping occur when sawing with a circular saw?

Again, plywood is simply multi-layer veneer glued together. The layers of veneer in different layers are directed alternately: a layer with one fiber direction, a layer with a perpendicular fiber direction. If you cut plywood along the direction of the grain, then you most likely will not have problems. But if you cut across, the top layer of veneer chips. The disk rotates so that the teeth move from bottom to top, and they just lift up the top layer of veneer.

As seen. The length of the chips reaches 2 cm. Sometimes even more.

In the case of a circular saw, this is due to the fact that there is a gap of a couple of centimeters between the disk and the sole (platform) of the circular saw. It is precisely because there is nothing pressing the layer of plywood on top that these chips occur. Thinner discs (for example, for laminate) did not suit me either - the result is exactly the same.

I am calibrating the saw

I install the tilt regulator in the guides and carry out its alignment and calibration. To do this, I use a metalworker's square and a water level.

I'm cutting

I make a small test cut. To do this, I first made a pencil line that intersects the diagonal edges of the two triangles on the workpiece. Then he clamped it with clamps and sawed it along the line.

I make sleds

Made a sled from some old bed frame steel and a piece of wood to get a clean edge. I screwed the bar to the corner with several screws.